June 29, 2016
June 29, 2016
June 29, 2016
June 29, 2016
June 29, 2016
June 29, 2016
June 29, 2016
June 29, 2016
June 29, 2016
June 29, 2016
최근 게시물
I'm busy working on my blog posts. Watch this space!
추천 게시물
Moog | MF-104M MOOGERFOOGER ANALOG DELAY
January 13, 2016

Moogerfooger
Moogerfooger Analog Effect Module의 세계에 오신 것을 환영합니다. Moogerfooger는 오리지널 모쥴러 Moog 신디사이저의 직계 후손들입니다. 견고한 금속과 목재로 마감되어 시간을 초월한 멋진 외관, 다재다능한 기능, 뛰어난 사운드 퀄리티로 작업실, 무대, 스튜디오 어디서든 놀라운 사운드를 만들어 냅니다. 따뜻한 아날로그 사운드와 결합한 광범위한 기능성은 모두 Bob Moog의 개인적인 지시아래 제작되었으며 최신의 완벽한 아날로그 회로에 의해서 만들어집니다. 음악적이며, 유연한 사용과 함께 다루기 쉽고 내구성이 뛰어난 Moogerfooger는 일류 연주자들과 프로듀서들의 비밀 병기입니다.
Moogerfooger MF-104M Analog Delay
Bob Moog가 제작하여 2000년에 발표한 오리지널 모델인 Classic MF-104 Analog Delay는
1000대의 한정판으로 제작되었습니다. 특수한 “Bucket Brigade” 칩을 사용해 완벽한 아날로그 이펙트로 완성시켰습니다. 하지만 불행히도 이 칩의 공급에는 한계가 있어서 2001년에 마지막 MF-104가 판매되었습니다.그 이후로 Classic MF-104의 두 가지 리이슈인 MF-104Z와 MF-104SD가 제작되었습니다. 당시, 각 모델은 역사상 가장 사람들이 많이 찾는 아날로그 딜레이로 기록되었습니다.
MF-104M은 Classic MF-104의 사운드와 분위기를 재현했습니다. 그리고 오리지널 모델에서 사용된 동일한 빈티지 “Bucket Brigade” 딜레이 칩을 사용해서 지구상의 모든 아날로그 딜레이 중에서 가장 풍부하고 크리미한 800ms의 아날로그 딜레이를 만들어냅니다.새로운 6개 파형의 LFO는 이 Classic Analog Delay의 능력을 놀랍도록 확장시켜줍니다. 시간에 따라 점점 확장되고 아름답게 딜레이 여음을 모쥴레이트하는 사운드를 만들거나 간단하게 환상적인 사운드와 딜레이를 만들어 낼 수 있습니다.
Spillover 모드는 MF-104의 가장 인기 있는 기능이었고 MF-104M에도 탑재되어 있습니다.
딜레이를 껐을 때 딜레이의 여음을 유지시킬 것인지 즉시 멈추게 할지를 결정할 수 있습니다.
Tap Tempo 스위치로 Delay Time이나 LFO Rate를 조절할 수 있습니다. 그리고 추가된 MIDI 기능은 MF-104M에 컨트롤과 기능의 새로운 영역을 열어주었습니다. 모든 기능을 조절하고 컨트롤할 수 있습니다. 여러분의 스튜디오 프로덕션에 아날로그 딜레이를 추가해 사용하는 것도 멋진 방법입니다.
후면 패널에는 CV/Expression 페달 인풋이 있어서 핸즈-프리 컨트롤과 Time, Rate, Feedback, Amount, Mix를 조절할 수 있습니다. 모든 Moogerfooger와 마찬가지로, 이 인풋들에 Moog EP2 익스프레션 페달을 연결해 기능을 컨트롤하거나 다른 Moogerfooger와 연결해 새로운 이펙트를 창조해낼 수도 있습니다.
또한, 피드백 인서트로 다른 스톰박스나 아웃보드 이펙트를 딜레이라인에 패치시켜서 다양하고 창의적인 이펙트를 얻을 수 있습니다.
MF-104M도 한정 기간 동안만 판매됩니다. 모두 사라지기 전에 Analog 역사의 한 조각을 놓치지 마세요.
Specifications
Front Panel Features:
DRIVE: From -7dB to +28dB of input signal gain or attenuation
OUTPUT LEVEL: Use to optimize overall Output volume
MIX: Cross fader control to set the ratio of wet to dry signal
TIME: Control range of 40ms – 800ms of analog delay time
SHORT/LONG RANGE: Select between a short, bright delay 40ms to 400ms and a long, dark delay 80ms to 800ms
FEEDBACK: Continuous control of Delay line output fed back to Delay input from no Feedback to infinite.
WAVESHAPE: Selectable 6 Waveshape LFO for modulating the Delay Time
RATE: Controls the LFO Rate from 0.05 Hz to 50 Hz (Wider range available via CV and MIDI)
AMOUNT: Controls the overall Amount of LFO modulation of the Delay Time.
LEDs and Switches
TIME LED: The LED is Red when controlled by the Time knob, and Green when controlled by Tap Tempo.
LEVEL LED: Bi-Color LED displays input signal for optimum processing level.
BYPASS LED: When the effect is on the Bypass LED is green. When in Spillover mode the Bypass LED is orange. When the effect is off the Bypass LED is red
RATE LED: Indicates both the Rate and Waveform LFO settings. The LED is Red when the Rate is set from the front panel, Green when set by Tap Tempo, and Orange when the LFO is synced to MIDI clock. Note: When synced to MIDI clock, the Rate control is quantized to select only rhythmic subdivisions of the MIDI clock tempo.
TAP TEMPO: Tap Tempo control assignable to Delay Time or LFO Rate by holding down the switch. Time LED or Rate LED will flash Green to indicate Tap Tempo assignment.
SPILLOVER MODE: Press and hold Bypass to engage/disengage Spillover Mode.
REAR PANEL Features:
AUDIO IN: 1/4” TS jack that accepts any instrument level to line level audio signal.
MIX OUT: 1/4” TS jack with adjustable output level for instrument or line level output.
DELAY OUT: 1/4” TS jack that supplies wet-only output.
FEEDBACK, TIME, LFO RATE, MIX, LFO AMOUNT: All are 1/4” TRS jacks that accept Moog EP-2 (or equivalent) expression pedals, or 0-5VDC control voltages from either two-circuit (TS) or three-circuit (TRS) 1/4” jacks.
FEEDBACK INSERT: 1/4” TRS jack for inserting effects on the feedback loop of the Delay Line. Supplies line-level output.
MIDI IN: 5 Pin DIN input for controlling the MF-104M via MIDI.
+9VDC POWER JACK: Accepts standard 9 volt center positive barrel power adaptor (power adaptor included). 400mA minimum required.
General Specifications
CASE: Black panel with hardwood sides – classic analog appearance.
DIMENSIONS: 9″ x 6″ x 2-1/2″
NET WEIGHT: 3 lb
SHIPPING WEIGHT: 5 lb, including power adaptor and instruction manual.
POWER REQUIREMENTS: 105-125AC, 5W. 220AC 50Hz either European or UK style power adaptor available on special order.
Tags:


